濟南膩?zhàn)臃墼谑褂眠^程中處理，而拋光時的時機把控尤為關鍵，不少人對此并不熟悉。濟南膩?zhàn)臃墼撊绾握莆諕伖夥椒?？下面為大家介紹相關知識。

　　Jinan putty powder is processed during use, and the timing of polishing is particularly crucial, which many people are not familiar with. How to master the polishing method of Jinan putty powder? Below, we will introduce relevant knowledge to everyone.

　　并非所有膩?zhàn)佣歼m合拋光，濟南地區常用的可拋光膩?zhàn)佣酁榉麓赏苛匣蚰退佔印Ｊ┕r(shí)先批刮一遍膩?zhàn)诱置嬲移?，待干燥后用砂紙打磨，再批刮第二遍，待其八成干時用批刀將表面壓平并磨出光澤即可。

　　Not all putty is suitable for polishing, and the commonly used polishable putty in Jinan area is mostly porcelain like coating or water-resistant putty. During construction, first apply a layer of putty to level the surface. After it dries, use sandpaper to polish it, and then apply a second layer of putty. When it is 80% dry, use a trowel to flatten the surface and polish it to a glossy finish.

　　內墻膩?zhàn)用鎸訏伖庑璋盐蘸线m時機，最佳時段是膩?zhàn)颖砻嫠∠Ш?，立即進行拋光操作。

　　The polishing of the inner wall putty surface layer should be done at the appropriate time, and the best time is to immediately carry out the polishing operation after the watermark on the putty surface disappears.

　　產品務必在保質期內使用，若超過保質期，必須先進行試刮，檢驗合格后方可施工。

　　The product must be used within its shelf life. If it exceeds the shelf life, it must be scraped and inspected before construction can begin.

　　產品需注意防水，應存放在陰涼干燥處，且保證包裝完好。

　　The product should be waterproof, stored in a cool and dry place, and ensure that the packaging is intact.

　　夏季或高溫天氣下，施刮膩?zhàn)忧敖ㄗh先用清水潤濕墻面，待墻面表面無明水后再進行膩?zhàn)邮┕巍?/p>

　　In summer or hot weather, it is recommended to wet the wall with clean water before applying putty. Wait until there is no visible water on the wall surface before applying putty.

　　墻面刮過濟南膩?zhàn)臃鄹稍锖笕舫霈F(xiàn)暗黃狀態，可用拋光機拋光一次，再用砂紙打磨，重復三次，最后用拋光機拋光無需砂紙打磨。新的拋光操作需用 500 目的細砂紙加水打磨；膩?zhàn)庸魏煤笤谄叱啥喔蓵r(shí)拋光一次，待九成干（從側面看部分墻面干透略顯發白）時再拋光一次，基本就能達到光亮效果。其實只要進行拋光通常都會有光澤，只是從側面觀察更為明顯，操作得當便能實現既光亮又順滑的效果。

　　If the wall surface appears dark yellow after being scraped with Jinan putty powder and dried, it can be polished once with a polishing machine, then sanded with sandpaper, repeated three times, and finally polished with a polishing machine without sandpaper. The new polishing operation requires 500 grit fine sandpaper and water to polish; After scraping the putty, polish it once when it is over 70% dry, and then polish it again when it is 90% dry (some walls appear slightly white when viewed from the side), which can basically achieve a bright effect. In fact, as long as polishing is carried out, there is usually a luster, but it is more obvious from the side view. Proper operation can achieve both a bright and smooth effect.

　　濟南膩?zhàn)臃鄣恼{(diào)配較為簡單，需搭配液體進行。如今許多防水膩?zhàn)臃壑恍栌们逅{(diào)配，使用方便；還有一種耐水性較差的膩?zhàn)臃郏杓尤肽z水調配，但這類膠水環保性欠佳，因此建議購買無需添加膠水的膩?zhàn)臃?。膩?zhàn)臃鄣臄嚢枰埠苤匾璋盐蘸脭嚢钑r(shí)間和力度。膩?zhàn)映浞謹嚢韬螅o置 15-20 分鐘，讓其中的添加劑充分溶解。

　　The mixing of Jinan putty powder is relatively simple and requires the use of a liquid. Nowadays, many waterproof putty powders only need to be mixed with clean water, which is convenient to use; There is also a type of putty powder with poor water resistance that needs to be mixed with glue, but this type of glue has poor environmental protection. Therefore, it is recommended to purchase putty powder that does not require glue. The mixing of putty powder is also important, and it is necessary to grasp the mixing time and intensity. After the putty is fully mixed, it should be left to stand for 15-20 minutes to allow the additives to dissolve completely.

　　濟南膩?zhàn)臃圩鳛榻ㄖb修材料的一種，主要成分包含滑石粉等。新房毛坯房表面的一層白色物質便是膩?zhàn)樱ǔＤ佔拥陌锥仍?90 以上，細度在 330 以上。膩?zhàn)佑糜趬γ嫘扪a(bǔ)找平，為后續裝修（如刷油漆、貼壁紙）打下良好基礎。膩?zhàn)臃譃閮?nèi)墻和外墻兩種，外墻膩?zhàn)右蛐璧钟L(fēng)吹日曬，膠性大、強度高，環保指數稍低；內墻膩?zhàn)泳C合性能較好，健康環保，因此內墻不外用，外墻不內用。

　　Jinan putty powder, as a type of building decoration material, mainly consists of talcum powder and other components. The layer of white substance on the surface of a new bare house is putty, usually with a whiteness of 90 or above and a fineness of 330 or above. Putty is used for wall repair and leveling, laying a good foundation for subsequent decoration such as painting and wallpaper. Putty is divided into two types: interior wall putty and exterior wall putty. Exterior wall putty needs to withstand wind and sun exposure, has high adhesive properties, high strength, and slightly lower environmental protection index; Interior wall putty has good comprehensive performance, is healthy and environmentally friendly, so it is not used externally for interior walls and not used internally for exterior walls.

　　通常膩?zhàn)右允嗷蛩酁榛?，表面粗糙，便于粘接牢固。但施工時仍需在基層涂刷一層界面劑，以封固基層并提高墻面附著力，讓膩?zhàn)痈玫卣辰Y(jié)在基面上。

　　Usually, putty is based on gypsum or cement, with a rough surface that is easy to bond firmly. But during construction, it is still necessary to apply a layer of interface agent on the base layer to seal it and improve the adhesion of the wall, so that the putty can better bond to the base surface.

　　本文由濟南膩?zhàn)臃?/a>友情奉獻.更多有關的知識請點擊:http://www.chnzylw.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan gypsum powder For more information, please click: http://www.chnzylw.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.